Serving Northwest Florida & Lower Alabama
Free Estimates Mon–Sat, 6 AM – 6 PM (850) 910-2447
Before and after of tall growth around a raised house cleared down to open ground with a skid steer
Call (850) 910-2447 Get a Free Quote

How much does a driveway culvert cost in Florida?

Bob Vila puts a driveway culvert at about $1,500 to $5,000 installed. Angi puts professional culvert replacement at $1,000 to $9,000, with an average around $4,500. HomeGuide prices culverts or drains on a gravel drive at $500 to $2,000. Pipe length, pipe type and the county’s rules decide where a Florida job lands.

A driveway culvert is the pipe that carries the roadside ditch under your entrance. Our driveway culvert installation page shows how that work goes in Northwest Florida. The prices in this guide come from Angi, HomeGuide and Bob Vila. The rules come from Santa Rosa, Escambia and Okaloosa Counties and the state.

What does a driveway culvert cost installed?

National cost guides put an installed driveway culvert anywhere from $500 to $9,000, and each guide draws its own bracket. Angi puts professional culvert replacement at $1,000 to $9,000. Its average sits around $4,500. Angi ties the spread to culvert length, pipe type and driveway material.

Bob Vila puts installing a culvert under a driveway at about $1,500 to $5,000. HomeGuide’s figure runs lowest. Its gravel driveway guide prices culverts or drains at $500 to $2,000, as one line inside a gravel drive budget.

What the price covers matters as much as the number. Angi says the professional price usually includes resurfacing the part of the driveway over the pipe. It may or may not include stone, rock or sod to line the ditch. Two quotes can sit far apart on paper for that reason alone.

How much does culvert pipe cost by material?

Angi prices a 24 inch by 20 foot length of aluminum or galvanized steel pipe at about $800. A plastic pipe of the same size runs $700. Angi says culvert pipes are usually aluminum, galvanized steel, plastic or concrete. It gives no price for concrete.

Pipe materialAngi price, 24 inch by 20 foot lengthStrong pointsWeak points
Galvanized steelAbout $800Strength and durability for high trafficProne to rust, which can create weak spots
AluminumAbout $800Will not rustNot as strong as steel
Plastic$700Lightweight and easier to installNot as strong as steel, better suited to low traffic
ConcreteNot priced by AngiDurable and suited to high trafficHeavy, needs more manpower, and cutting it takes extra machinery

Service life is the other half of the choice. The FDOT drainage manual estimates 100 years for Class II HDPE plastic pipe. It puts Class I HDPE at 50 years. Angi’s prices cover one 20 foot length, and a wide entrance takes more than one.

What moves the price of a driveway culvert?

Pipe length, pipe size, ditch depth, end treatments and the drive on top move the price. Each one changes the pipe bill or the machine time.

Pipe length and frontage. A single entrance pipe is the short end of the job. Santa Rosa County’s code can require pipe along the entire frontage of the lot, capped at 150 feet. That applies when Public Works finds the ditch constantly remains wet from flat elevations or a high water table.

A 150 foot run is seven and a half of Angi’s 20 foot lengths. At Angi’s 24 inch prices, that is roughly $5,250 to $6,000 in pipe alone.

The inspector’s size and type call. Where a Santa Rosa permit applies, the county inspector sets the pipe elevation at the line and grade inspection. The inspector also provides the pipe size and type. A wider pipe or a different material changes the pipe bill before any digging starts.

On state road work, the FDOT drainage manual sets a 15 inch minimum for side drains. Some locations require 18 inches. Angi’s national guide runs smaller, at a typical 10 or 12 inches.

Ditch depth and fall. The pipe has to carry the ditch without blocking it. Santa Rosa’s code says construction shall not obstruct stormwater movement in any way. A deeper ditch means more digging and more backfill around the pipe.

Santa Rosa’s code says the county Road and Bridge Department sets the line and grade. Correct installation to that line and grade is the permittee’s responsibility. In Okaloosa County, the permit form points applicants to the county’s Engineering Department to have grade set in the ditch.

End treatments. The ends of the pipe add cost too. Santa Rosa’s driveway page lists mitered ends as required on a culvert drive. The county code requires them when the permit specifies them, and it requires sod at the ends of the pipe.

The drive on top. The surface over the pipe is its own line. On a Santa Rosa culvert drive, the inspector checks the form boards at the pre-pour. At the final, two rows of sod are required around any concrete.

The final also checks that no dirt sits inside the pipe. The gravel side of the drive, from stone to base depth, is in our gravel driveway cost guide.

Is replacing an old culvert different from putting in a new one?

Yes, because a replacement starts with tearing out the old pipe. Angi says a rusted-out or damaged culvert is generally not worth repairing. Replacing it takes less time and will likely last longer than a repair.

The warning signs show up at the end of the drive. Angi says water can build up at the end of your driveway without proper drainage from a culvert. A pipe that was not installed right can buckle or crack under the weight of a car. A crushed or silted pipe backs water up at the entrance, and the drive above it starts to wash.

In Santa Rosa County, the ditch itself is county business. The code bars anyone from filling, blocking or altering a county drainage ditch without prior approval. That approval comes from Public Works. A new entrance on a county-maintained road always needs a permit before work starts.

A drive that keeps washing out over an old pipe often needs its shape fixed as well. That reshaping is grading and dirt work, done while the machine is already on site.

Which permit does a driveway culvert need in Santa Rosa, Escambia or Okaloosa?

It depends on who maintains the road your driveway meets. Santa Rosa County requires a county permit and inspections when the driveway attaches to a county-maintained road. A line and grade, a pre-pour and a final are required. The permit goes void in 18 months if the work is not completed.

Escambia County routes driveway work in county right of way through a Right-of-Way Utilization Permit from Public Works. Okaloosa County issues its own driveway permit for county-owned right of way. An Okaloosa permit lapses if the driveway is not built within 90 days of approval.

State and city roads have their own offices. Santa Rosa’s driveway page sends you to the state or city when one of them maintains the road. For state roads, Rule Chapter 14-96 of the Florida Administrative Code governs connections to the State Highway System.

Utility lines get marked before any digging. Santa Rosa’s code makes the permittee responsible for notifying all utility companies for locates.

How much does a driveway culvert permit cost?

Bob Vila says driveway permits typically cost $50 to $200, depending on location. Next to the installed ranges above, the permit is a small line.

On Santa Rosa County’s mobile home permit application, the driveway permit is listed at no fee. The county code lets the board of county commissioners set permit fees by resolution. Ask Public Works what your project carries before the work starts.

Can you install a driveway culvert yourself?

You can rent the machines, but the county rules still apply to the pipe. Angi’s DIY list puts a skid steer loader at about $200 a day to rent. A vibrating compactor runs $83 a day to rent, and a backhoe attachment $40 a day.

Angi says a larger project may require heavy equipment. Santa Rosa’s code says the permittee will furnish, install and cover the culvert pipe per county specifications. On a county-maintained road, the line and grade, the pre-pour and the final still apply to a homeowner’s own work.

Why does a culvert price need an on-site look?

A culvert price needs an on-site look because the ditch sets most of the job. Its depth, its fall and whether it stays wet only show up at the property. On a Santa Rosa county road, the size and type call comes at the line and grade.

Two entrances on the same road can need very different pipe runs. One ditch drains, and the next stays wet enough for pipe across the whole frontage.

Clearview Contracting Solutions sets driveway culverts and builds the drives over them across Santa Rosa, Escambia and Okaloosa Counties. Twenty-plus years of running machinery sit behind the company. Free on-site estimates come with a written number. To get one for your entrance, contact us or call (850) 910-2447.

Frequently asked questions

How much does it cost to install a culvert under a driveway?
Bob Vila puts a culvert under a driveway at about $1,500 to $5,000. Angi puts professional culvert replacement at $1,000 to $9,000, with an average around $4,500. Angi ties the spread to culvert length, pipe type and driveway material. HomeGuide prices culverts or drains on a gravel driveway lower, at $500 to $2,000.
How much does culvert pipe cost?
Angi prices a 24 inch by 20 foot length of aluminum or galvanized steel pipe at about $800. A plastic pipe of the same size runs $700 in the same guide. Angi gives no price for concrete pipe. The pipe is only part of the bill. Digging and the drive over the pipe add to it.
What size culvert pipe does a driveway need?
In Santa Rosa County, the permit inspector provides the pipe size and type at the line and grade inspection. On state road work, the FDOT drainage manual sets a 15 inch minimum for side drains. Some locations require 18 inches. Angi's national guide says driveway pipe is typically 10 or 12 inches.
Who pays for the culvert pipe in Santa Rosa County?
The permit holder pays. Santa Rosa County's code says the permittee will furnish, install and cover culvert pipe, if needed, per county specifications. The county's Road and Bridge Department sets the line and grade. Correct installation to that line and grade is the permittee's responsibility. Angi says the homeowner maintains and repairs the culvert in most cases.
Why would the county require pipe across my whole lot?
Santa Rosa County's code covers this case. Public Works may find that the ditch constantly remains wet from flat elevations or a high water table. Then the applicant must install culverts along the entire frontage of the lot. That run is capped at 150 feet. The county's driveway page says some areas require it.
Should I repair or replace a crushed driveway culvert?
Angi says a rusted-out or damaged culvert is generally not worth repairing. A replacement takes less time and will likely last longer than a repair. Angi puts professional culvert replacement at $1,000 to $9,000. In Santa Rosa County, altering a county drainage ditch takes prior approval from Public Works.
How much does a driveway culvert permit cost?
Bob Vila says driveway permits typically cost $50 to $200, depending on location. On Santa Rosa County's mobile home permit application, the driveway permit is listed at no fee. The county code lets the board set permit fees by resolution. Ask the county's Public Works office what applies before the work starts.
Ready to Take Your Land Back?

Get In Touch With Clearview

Overgrown lot, pasture edge gone wild, hunting land that needs trails and plots, a stump that has been there too long? Call or send the form, and we will look over the property with you and hand you a free estimate with a written number.

  • (850) 910-2447
  • Mon–Sat, 6 AM – 6 PM
  • Serving Northwest Florida & Lower Alabama
  • Free estimates with a written number

Get a Free Quote

Tell us about your project — we’ll get right back to you.

Call (850) 910-2447